Fluid Lab Report

In: Science

Submitted By kunal24
Words 367
Pages 2
Experimental Observations

This section of the report contains results from experimental observation of the R713 Hilton refrigeration unit during its operation. The experimental result are required for calculations relevant for the analysis of the first law within the unit;

Ambient Temperature: 22.2 (C

Ambient Pressure : 754.9 mm Hg

Compressor Speed: 472 rev/min

Load on Dynamometer arm 9.25 N

Evaporator Current: 4.5 A

Evaporator Voltage: 200 V

Condenser Flow Rate: 483 g/s

Condenser Temp (inlet) 13.7 (C

Condenser Temp (exit) 20.8 (C

Condenser Pressure: 590 kPa (gauge)

Evaporator Pressure: 190 kPA (gauge)

Compressor Temp (inlet) 9.6 (C

Compressor Temp (exit) 43 (C

Condenser Temp (exit) 23.7 (C

Evaporator Temp (inlet) 0.4 (C

Calculations

Mass flow rate of R134a around Evaporator

Q L = (V)(A) = (200)(5.4) = 1080 kW

P3 = 590 kPa h3 = h4 = 265 kJ/ kg (from table)
T3 = 23.7 (C

P1 = 190 kPa h1 = 261 kJ/ kg (from table)
T1 = 9.6 (C

Q L = m (h1 – h4)

m = 1.080 / (261 – 265) = 0.270 kg/s

Mass flow rate of R134a around Condenser

QH = mcw * Cp (water) (Tcw, in – Tcw, out) = (0.483)(4.18)(13.7 – 20.8) = 14.33 kJ/s

P2 = 590 kPa h2 = 283 kJ/ kg (from table)
T2 = 43 (C

P3 = 590 kPa h3 = h4 = 265 kJ/ kg (from table)
T3 = 23.7 (C

QH = m (h2 – h3)

m = 14.3 / (283 – 265) = 0.8 kg/s

Power input to the Compressor

Ps (shaft power) = F * (0.053218) * nc = (9.25)(0.053218)(7.87) = 3.82 kW

Power Factor = Pa / Ps
Pa = (0.57)(3.87) = 2.207 kW

Calculations Continued

Coefficient of Performance for the Refrigerator

( = QL / Wc

Wc = Pa

( = 1.080 / 2.207 = 0.49

Rate of Heat Transfer from the Compressor

Win = Qout + m (he – hi)…...

Similar Documents

Lab Report

...Crowder-Gross Lab 2 Report 3-In this activity you learn open Server Manager and then see what all the different things it can do. For instance, if you are working in Active Directory, you can create a new user account, set up a shared folder, or change to a different domain. What are the topics for additional information? The topics for additional information overview of print services, migrate print servers, control printer driver security, update printer drivers, and resources for print management. Note Installation Results The results showed that the installation attempts failed. 3-3 For this section you use ServerManagerCmd.exe to install the Print Services role, query the installed roles and features, and then remove the Print Services role. ServerManagerCmd.exe is designed to help the installation of multiple servers and for the server administrator who prefers to work from the command line. Record observations about the purpose of each tab Advance tab- shows what properties are available for the network adapter Driver tab- shows detail of the driver Details tab-shows device description Resources tab- shows the range of the resources Power management- shows different ways to save power Are any resources conflicts reported? How would you solve a resource conflict? There are not any conflicts reported. 3-10 This activity is done to learn where to configure the system and user environment variables and at the same time determine which ones......

Words: 318 - Pages: 2

Lab Report

...Lab 1: Introduction Metric System Prefixes (to put in front of basic units): k = kilo = 1000 x c = centi = 1/100 of (which is 10-2 of) m = milli = 1/1000 of (which is 10-3 of) ( = micro = 1/1,000,000 of (which is 10-6 of) n = nano = 1/1,000,000,000 of (which is 10-9 of) (d = deci = 1/10 of ) [pic] (Note: The way to read the numbers above, for example, is: There are 1000 nm in one (m. There are 1000 (m in one mm.. etc.) To convert from one metric unit to a different metric unit (a different prefix): 1. First, decide how many places to move the decimal point (the number of 0’s in the chart above indicates the number of places to move the decimal point). 2. Next you need to decide whether to move the decimal point left or right. To decide this, think about which is the smaller unit. (The smaller the unit is, the more of them you need to get the same amount. e.g. pennies vs. dollars) NOTE: Here is another way to write the conversions, using distance (the meter is the basic unit for distance) as an example: 0.001 km = 1 m = 10 dm = 100 cm = 1000 mm = 1,000,000 (m = 1,000,000,000 nm The “staircase” method: One more way to remember about sliding decimal points when converting between prefixes in the metric system! [pic] Move the decimal point 3 places for every step you move on the “staircase”, and in the same direction traveled on the staircase (left vs. right). Unfortunately, you can see that the “c”......

Words: 1090 - Pages: 5

Lab Report

...CN3108: CHEMICAL ENGINEERING PROCESS LAB II Experiment B1 Adsorption for Protein Isolation (L) Frederick Chan Yew Meng U065963A (E) Gan Yue Sern U065873B (A) Giam Ming Yao Joshua U065944X (R) Farhana Mehnas D/O Haja N U065763H Group: M4 Submitted On: 13th October 2008 Contents Sections Page Summary 1 I Introduction 2 II Theoretical Background 3 III Experimental procedures 6 IV Results and Analysis 8 V Discussion 22 VI Conclusion 28 VII References 28 Summary This experiment was to determine the adsorption isotherm for bovine serum albumin (BSA) on an anion-exchange adsorption resin with a model that is derived from the experimental data and to draw a breakthrough curve for BSA for different superficial velocities and find out the controlling step occurring within the packed bed. The Freundlich Isotherm q=αC1v was then found to be a better model to approximate the adsorption isotherm for BSA as compared to Langmuir Isotherm. From the experimental data, the static capacity determined from Langmuir Isotherm approximation was estimated to be 330.033mg/g and the dynamic capacities flow rates of 5.0, 2.5, 0.5 ml/min were 0.918, 1.431 and 2.066 mg/g respectively, thus agreeing with theoretical knowledge that the static capacities should be larger than dynamic capacities as sufficient time were allowed for......

Words: 5317 - Pages: 22

Lab Report

...Lab 6: How to Write a Lab Report (1) Atta, S., M. Ikbal, A. Kumar, and N. D. Pradeep Singh. 2012. Application of photoremovable protecting group for controlled release of plant growth regulators by sunlight. Journal of Photochemistry and Photobiology B: Biology 111:39-49. --This article shows that sunlight is the key requirement for plant growth. It explains how sunlight helps in releasing plant growth regulators in plants which enhances plant growth. This article is helpful for my lab report because we provided sunlight to our plants which makes their development faster. (2) Ikram-ul-Haq, Z. A., G. M. Taseer, M. U. D. Mukesh, and S. Ali. 2011. Effects of different fruit juices used as carbon source on cucumber seedling under in-virto cultures. African Journal of Biotechnology 10:7404-7408. --This article shows how fruit juices help plants to grow better because of the sugar that fruit juices contain. They used strawberry and apple juices, but they were not as good as orange and grape juices, regarding their effect on plant growth. This article is helpful for my lab report because we used orange juice to measure its effect on the growth of our plants. (3) Einset, J.W. 1978. Citrus tissue culture: stimulation of fruit explants cultures with orange juice. Plant Physiology 62:885-888. --This article shows the effect of orange juice on plant growth. It explains how using high concentrations of citric acid does not enhance the plant growth, but using...

Words: 299 - Pages: 2

Lab Reports

...C8057 (Research Methods in Psychology): Writing Laboratory Reports Writing Lab Reports & APA Format Structure and Content of a Laboratory Report This following provides a brief overview of the structure and content of various elements in a laboratory report, based on APA guidelines. The APA publication manual can be referred to for more detail. The purpose of a lab report is to communicate research in a clear, systematic and standardised way. Primarily, a lab report should communicate the following things: → Why did I bother? Why did I do this experiment and why is it an interesting contribution to science? → How did I do it? How did I carry out this research (this should be detailed enough so that the experiment could be replicated precisely)? → What did I find? What were the results of your study? → So What? What do your findings mean in terms of your hypotheses and what theoretical contribution do they make? IMPORTANT! The advice that we give you in this handout is not inflexible, it is a guide! For example, when we say that the title should be fewer than 15 words, the world will not end if your title is 16 words. So, please use your common sense. In case you don’t have any, the snail of sense will appear to give you some advice. Format There are several sections to a lab report: → Title → Abstract → Introduction → Method o o o o o → Results → Discussion → References → Appendix (Optional) Title Your title should ideally be fewer than 15 words. A good title alerts the......

Words: 7238 - Pages: 29

Lab Report

...Introduction: In this lab, my partner Jacob Hodge and I will be doing four different experiments using a microscope. The purpose of this lab is to know the proper technique of focusing and making slides. In these experiments, Jacob and I will learn the parts of a compound light microscope, the functions of those parts, and the proper use and care of the microscope. We will also learn how to clean up wet mount slides. Objects, or specimens, to be observed under a microscope are generally prepared in one of two ways. Prepared or permanent slides are made to last a long time. They are usually purchased from biological supply houses. Temporary or wet mount slides are made to last only a short time-usually one laboratory period. In the 1600’s, Anton von Leeuwenhoek discovered the life that lives in a drop of pond water. This discovery opened up a new world for biologists that could be explored only with the aid of magnification. Since Leeuwenhoek’s time, the microscope has become one of the most important tools used by biologists. Much has been learned about the nature of life and about living things with the help of the microscope. Methods & Materials: Compound light microscope prepared glass slide lens paper newspaper beaker rubbing alcohol glass slide coverslip forceps pipette scissors kim wipes dark thread light thread medicine dropper pond water The steps or procedures of the regular class......

Words: 1916 - Pages: 8

Lab Report

...Weekly iLab iLab: Exploring the Microbiology Lab FirstName Tiffani_LastName: Whitehead Section 1 Lab Safety 1. There are four safety equipment items that a lab should have. Identify two of these four items. (2 pts) Biological Safety Cabinet, Eyewash and shower 2. Identify one of the three ways to keep your work area safe. (1 pt) Keep your workspace free of all unnecessary materials 3. There are five recommendations for dressing properly in a lab environment. Name two of these recommendations. (2 pt) Avoid loose fitting items of clothing, Wear appropriate shoes sandals are not allowed. 4. There are several safety tips to protect one’s mucous membranes and broken skin. Identify one of the recommended tips. (1 pt) Do not apply makeup, put in contact lenses, or otherwise perform activities that might introduce lab organisms to your personal space. 5. When working in a microbiology lab, it is important to contain spills and discard materials properly. Describe how a spill should be cleaned up safely in a microbiology lab. (3 pts) 1. Wear a lab coat, disposable gloves, safety glasses or a face shield, and if needed, approved respiratory equipment. 2. Soak a paper towel(s) in an appropriate disinfectant (70% ethanol or fresh 10% bleach solution) and place around the spill area. 3. Working from the outer edges into the center, clean the spill area with fresh towels soaked in the disinfectant. Be sure to decontaminate any areas or surfaces......

Words: 870 - Pages: 4

Lab Report

...Name: Gertrude Edwards Date: 12/1/2014 Instructor’s Name: Staci Lynn Assignment: SCI203 Phase 2 Lab Report TITLE: Speciation • Purpose o The purpose of this lab is to evaluate what would happen if a species within a population were suddenly split into 2 groups. • Introduction o If a population is divided indefinitely by a barrier members of the divided population will not have the opportunity to breed with each other, over years, the biotic and abiotic conditions on either side of the barrier will vary from one another. (M.U.S.E). • Hypothesis/Predicted Outcome o Based on what I’ve learned I expect that species will undergo changes if they were split into 2 different groups, some would adapt and some wouldn’t. • Methods o The methods I used in this lab came from M.U.S.E. The initial separation would consist of some species from the mainland reaching the isolated Island, then after that the isolated population would begin to diverge because of the genetic drift and natural selection, then after that overtime divergence may eventually become sufficient to cause reproduction isolation. (M.U.S.E). • Results/Outcome o As a result, Natural selection will cause different selective and adaptive pressures to occur between the two divided populations and they will evolve forever. Over time this will result in speciation which is the creation of two new species. (M.U.S.E). •......

Words: 309 - Pages: 2

Lab Report

...Lab Report Using Gravitational Force as a Measurement Tool Answer the following questions about the results of this activity. Record your answers in the boxes. Send your completed lab report to your instructor. Don’t forget to save your lab report to your computer! Activity 1 Record your data from Activity 1 in the boxes below. Enter the data for the sample you used in each trial (5000 rpm, 10000 rpm, etc…) in the appropriate columns and the corresponding g-force, number of layers, and position of layers position results. You will need to use the following formula to assist with your laboratory report: • G-force =0 00001118 x radius of centrifuge arm x (rpm)2 • The radius of the centrifuge arm for this instrument is 10 cm. | | | | | | |Speed |5000 rpm |10000 rpm |15000 rpm |20000 rpm | | |2795 |1180 |2655 |4720 | |G-force | | | | | | | |4 |5 |3 | |Number of......

Words: 436 - Pages: 2

Lab Report

...Dialysis and Osmosis Beitz 1 Introduction: The cell membrane is not a solid structure. It is made of millions of smaller molecules that create a flexible container. Proteins and phospholipids make up most of the membrane structure. “The proteins are found around the holes and help move molecules in and out of the cell. There are also proteins attached to the inner and outer surfaces of the membrane” (BiologyKids, 15). There are receptor proteins which receive specific molecules, and there are transport proteins. There are two types of transport proteins which only allow specific molecules to enter and exits, therefore selectively permeable. Releasing chemicals is called Exocytosis, and taking in chemicals is endocytosis. “Scientists use the fluid mosaic model to describe the organization of phospholipids and proteins. The model shows you that phospholipid molecules are shaped with a head and a tail region. The head section of the molecule likes water (hydrophilic) while the tail does not (hydrophobic). Because the tails want to avoid water, they tend to stick to each other and let the heads face the watery (aqueous) areas inside and outside of the cell” (BiologyKids, 15). The two surfaces of molecules create the lipid bilayer. The interior of the lipid bilayer is “oily” and flexible like a soap bubble. Osmosis is the diffusion of water across a selectively permeable membrane, which is a barrier that has holes large enough to allow water molecules to pass but small......

Words: 1217 - Pages: 5

Lab Report

...To do Lab Report for Single and Double Replacement reactions : This is a formal lab report. It must be typed or written by hand with blue or black ink. Make sure that you include the following: 1. Title 2. List of Materials 3. Safety that includes MSDS risk assessment for all the materials used ( instructions were given to you already and they are in Moodle) 4. Pre-lab questions 5. Data Tables with the results obtained ( observations and predictions) 6. Post Lab: Part I : Single Replacement Reactions a. For every reaction that took place you must write the balanced chemical equation b. Which metal reacted the most? c. Rank your metals from more to least active Part II: Double replacement Reactions a. For every reaction where you observed precipitate, write the complete balanced molecular equation, the complete ionic equation and the net ionic equation; use the solubility rules to identify the precipitate and the states of matter of each substance participating in the reaction. b. Which cation produced the most number of precipitates? c. Write general rules of solubility that you observed. 7. Final Conclusion and error analysis To do Lab Report for Single and Double Replacement reactions : This is a formal lab report. It must be typed or written with blue or black ink. Make sure that you include the following: 1. Title 2. List of Materials 3. Safety that includes MSDS risk assessment for all the materials used (......

Words: 374 - Pages: 2

Lab Report

...pull it apart sharply and quickly. 3. The putty is very bouncy as compared to the slime. 4. Wrote ink-based pen on some paper and placed the putty on it while applying pressure. When lifted, the ink is on the putty as it sticks on to it. Conclusion Like the slime, Silly Putty is also a shear-thickening substance. The shear-thickening behavior happens they form these short-lived cross-linking bonds.  Basically it grabs onto the polymer chains monetarily, releases quickly, and then it re-forms another cross-link in a different place. This grab-release process happens repeatedly and rapidly, but also not fast until it lets the fluid flow normally. It bounces and also has a rubbery texture. References http://www.rsccaerodefense.com/polymer-cross-linking.php#.VuJj8Jx96Uk http://courses.chem.psu.edu/chem112/materials/polymers.html Post-lab questions 1. When the sodium borate was added, the glue, water mixture got thicker and became more solid as we stir the mixture. 2. I feel that the glue will become even thicker and it will fasten the process of it changing from a liquid to solid. There will not be as much liquid left as compared. Experiment 2 Preparation of Alginate Spheres Introduction Sodium alginate is a natural gelling agent taken form the cell walls of brown algae. However, it only gels when it comes in contact with calcium. Sodium alginate has many uses other than specification such as thickening, general gelling, and foaming. Each of us have......

Words: 1120 - Pages: 5

Lab Report

...Lab Report Introduction: Natural selection relies upon the assumption that all organisms produce more offspring than can survive in an environment demonstration limited resources. The heritable traits that are best suited for a particular environment should be passed on at a greater frequency then those less adaptive traits. Natural selection is unique in that it leads to adaptive change, and these changes are likely to lead to increased survival and reproductive success. To sum up, natural selection is that organisms can survive only because they can suit to the changed environment which means those organisms also need to change with the environment all the time. Hypothesis: during the experiment, the forks out of all the “predators” should survive, and the peas out of all those “preys” will be survived. Material and Metnods: We will use 4 kind of beans (preys items) which are fava beans, white beans, red beans and peas. And we also have 4 mouthparts (predators) which are knives, forks, spoons and foreceps. First, we get 100 ml for each prey and spread them on the ground. And the students will be divided into 4 groups with those 4 different predators. Each group of predators include 6 student. And all of the predators will have a cup which will serve as the stomach into which the prey will be placed. We also have a timer and a security that will make sure the process is fair. Here we begin the game. The predators will be gathered, they will be instructed not......

Words: 806 - Pages: 4

Lab Reports

...04.03 Periodic Table - Lab Report Please complete the following lab report for assignment 04.03 Introduction to the Periodic Table. Take notes on the properties of the three types of elements. Metals|Good conductors of heat and electricity. Metal are ductile, and malleable. Not only have that metals also had a distinct shiny look which is called metallic luster.| Nonmetals|Poor in conducting heat and electricity generally as insulators, only at room temperature. Non-metals can be either solids or gases; they are neither ductile nor malleable. They are mainly either opaque or transparent.| Metalloids|Moderate at conducting heat and electricity, only solid at room temperature, can be ductile and malleable only to varying degrees. How at metallic luster in varying degrees.| Fill in the following data table as you complete the activity. Material|Conductivity(strong, moderate, none)|Ductility(ductile or not ductile)|Appearance(bright shine, moderate shine, or no shine)| 1|The light is bright.|Can be drawn into wire.|Shines brightly.| 2|The light is dim.|Can be drawn into wire|Shines moderately.| 3|There is no light.|Cannot be drawn into wire|Does not shine.| 4|The light is bright.|Can be drawn into wire.|Shines brightly.| Identify each of the following as a metal, nonmetal, or metalloid. Please use complete sentences to describe the observations that led you to identify each. Material 1: Metal- Because it can be drawn into wire, shines brightly, and the......

Words: 357 - Pages: 2

Lab Report

...Why do we keep a lab notebook? In the ‘real world’, you will be expected to record what you do and how you do it, with the data clearly identifiable. There are 2 reasons for this: • Any scientific experiment is only considered valid if it can be repeated by someone else using your notebook. • If you develop a new product or process, your notebook becomes a legal document that can be scrutinized in a court of law, especially in cases of patent infringement. In order to meet these requirements, certain conditions must be met: • Notebooks shall have bound pages, loose-leaf and spiral bound are not acceptable. • All pages must be numbered prior to use. This will show if any pages have been removed that contained data that might compromise interpretation of your conclusions. • All data shall be entered chronologically. Do not leave empty pages to insert information later. If you finish with a large expanse of blank page, put a line through it to show that it will not be used. • All notes are to be made in indelible pen – pencil will be penalized. If you make a mistake, just draw a single line through it, not a childish scribble to hide all traces! • All data will be recorded in your lab notebook at the moment it is generated. No notes shall be written on scraps of paper or memorized for later. Other notes about the lab notebook: All pre-lab and experimental work is hand-written in your lab notebook. ......

Words: 1389 - Pages: 6