In: Computers and Technology

Submitted By zokenod
Words 365
Pages 2
When performing a cable installation there are a lot of things that you have to put into consideration. You want to draw up a plan first and some things that you would want to include in the plan would be where your telecommunications rooms are located, What is the distance from your leased line to your core router, and what type of cable are you going to be using for your backbone and horizontal lines. The first thing shouldn’t be cost when you are designing a network. You want to think of the safety and how your network will function with different mediums of cable. This things are important because your network to meet the needs of the company. You also want to make sure you have things in place like what type of fire protection your network will have. You want to make sure your racks in your telecommunication rooms are grounded properly. Without these things your network will not be very safe. You want it to be useful but you don’t want to lose everything in a telecommunications room because you failed to plan ahead for accidents that can happen.
Well once you have your plan intact and it has been approved you need to think about how you are going to get this cable in the building. What types of tools are you going to need? If you are going to run CAT 5e though out the building you will need several different tools; such as cable pulleys, punch downs, wire cutters, and cable strippers. You will need most of these tools to install your cable into your building. There will be a few different tools you will need if you are putting cable into a preexisting building. You may then need a fish tape or fiberglass push pole. It really depends on the type of job you are going to be doing and what type of cable or fiber you are going to be working with. This will determine what tools you will need to get the job done correctly and safely.
If you are at a worksite and…...

Similar Documents

Cabling Notes

...Notes What is the speed of light- 186000miles a second or 700 million miles an hours?How fast dose sound travel.-340mdHow fast dose sound travel in water -33502mph | Cabling Notes 6/20/12 Name three rules of Data cabling 1. Networks never get smaller or less complicated. 2. Don’t scrimp on installation cost. Quality components and cable must be installed, No poor workmanship allowed. 3. Plan for higher –speeds technologies than are commonly available today. Just because 1000Base-TEthernet seems unnecessary today doesn’t mean in five years you will need to use it. The cost of poor cabling – The cost that results from poorly planned and poorly implemented cabling systems can be staggering. Robert Metcalfe (Inventor of the Ethernet, founder of 3Com, columnist for InfoWorld, and industry pundit). Drop-rate magnification-The high degree of network problems caused by dropping a few packets. Note: a single dropped packet may cause an entire stream of packets to be retransmitted. ANSI-(American National Standards.) Application- a program on a computer. A system, the transmission method of which is supported by telecommunications cabling, such as 100Base-TX Ethernet, or digital voice. Digital- on the other hand is breaking the signal into a binary format where the audio or video data is represented by a series of "1"s and "0"s. Simple enough when it's the device—analog or digital phone, fax, modem, or likewise—that does all the converting for...

Words: 910 - Pages: 4

Lab9 Cabling

...required network cabling, termination points/boxes and necessary network devices. Mating sleeves, bare fiber adapters and optical attenuators are a few things that are needed specifically for fiber installation. In addition, the purpose would also include the proper details and criteria for the successful design of the network system. The contractor shall provide all of the necessary cables, network equipment and components necessary to construct the network system. This includes all raw materials such as cable, wall plates, outlet boxes, and such terminating modules and components as necessary to complete the job as contracted. Devices like test kits, power meters, fault locators, and connector adapters are all pre purchased and is property of the installing company. This document provides all of the necessary specifications to be used in the design of the network infrastructure and associated equipment. The contractor shall furnish all labor, materials, tools, equipment and reasonable incidental services necessary to complete an acceptable installation of the network infrastructure as contracted. Business Case Your network will be FTTB (Fiber to the Building). This means that the fiber will run to the main building and that will give you the ability to use fiber throughout the entire complex or the use of high-bandwidth copper cabling can be used. For the wired portion of the building and the telecommunications room, we will be using 62.5/125 cabling. Each room......

Words: 1246 - Pages: 5

Cabling Assignment Two

...CABLING ASSIGNMENT TWO 04/12/2012 (1) Identifying the important network topologies for commercial building. (a)What is the most typical implementation of the hierarchical star, that is, the specific location of the horizontal cross connection and the workgroup switches? ANS: They can be placed in the telecommunication room on each floor of the building (b)What is the process of locating the locating the network element closer to the equipment room is call and what are the benefits? ANS: This process is called FTTE (fiber to the telecommunication enclosure) and the benefits involved saving up to 25% or more through better port utilization and lower building costs of telecommunication rooms. (c) By installing all network equipment in a central location, what is the implementation of the hierarchical star topology called and what are the pros and cons? ANS: It is called FTTD (fiber to the desk) or centralized cabling and the good side of it is that it provides the greatest port utilization and reduces the size and load of the telecommunication room. At the opposite end, it is more expensive to use media converters or optical NICs (2) With the understanding of the different between UTP and Optical Fiber cabling and their places, with the many types of UTP and Fiber Cable: (a) What is the preferred UTP cabling media used to support 10Gbps network speed? ANS: Category 6A cabling (b) What is the preferring optical fiber cabling media used to......

Words: 360 - Pages: 2

Cabling Assignment 1

...the end users’ requirements and specify products that will support them. Since you must ensure that the product is specified per recognized U.S. industry standards, you will be careful to identify that the customer request references the appropriate application and cabling standards. What industry standards body and standards series numbers do you need to reference for Ethernet applications and cabling? The IEEE maintains the industry standards for Ethernet protocols (or applications). This is part of the 802.3 series of standards and includes applications such as 1000Base-T, 1000Base-SX, 10GBase-T, and 10GBase-SR. 2. An end user is interested in ensuring that the network cabling they install today for their 1000Base-T network will be able to support future speeds such as 10Gbps to a maximum of 100 meters. They have heard that Category 6 is their best option. Being well versed in the ANSI/TIA-568-C standard, you have a different opinion. What are the different types of Category 6 cable and what should be recommended for this network? There is the Cat 6 and Cat 6A and Category 6A would be recommended for the network since it was intended for 10Gbps networking. 3. Your customer is installing communications cabling in a factory full of stray EMI. UTP is not an option and a shielded cable is necessary. The customer wants to ensure capability to operate at 10GBase-T. What cable would you recommend to offer the best shielding performance? The best possible cable would be......

Words: 546 - Pages: 3

Cabling Definitions Unit 4

...Definitions Horizontal Cable – cable between telecommunications outlet and the horizontal cross-connect Backbone Cable – cable between telecommunications and equipment room Patch Cord – cable between network device and main cable run or outlet Connectors – device attached to end of “cabling” that attaches to another Conduit – section in which cables are housed for protection Racks – frame where panels, switches, and other equipment are installed Punch-Down Blocks – cross connect block where the wires are placed into a terminal groove and “punched down” with a special tool Consolidation Points – location for interconnection between building and work area pathways Crimpers – device used to install a crimp on connector Fish Tape – tool used to route wiring through walls or conduit Cable Toner – electronic device used to test cables for breaks and other problems Continuity Tester – device used to test cables for uninterrupted pathway for signal Category 5e/6 Cable – twisted pair cable with 100 ohm impedance and 100mhz freq. Binder Groups – group of 25 or more twisted pair wires Hybrid/Composite Cable – cable that has at least 2 types of media inside Pulling Cable – used to pull cable through conduit or over racks (similar to fish tape) Wavelengths of Light – distance an electromagnetic wave travels in the time it takes to oscillate through a complete cycle EMI – noise generated in copper conductors Optical-Fiber Strand – assembly consisting of one or more......

Words: 304 - Pages: 2

Cabling and Fiber Optic

...of the radiation and bounces the waves away from the surface. The simplest example of visible light reflection is the surface of a smooth pool of water, where incident light is reflected in an orderly manner to produce a clear image of the scenery surrounding the pool. Throw a rock into the pool, and the water is perturbed to form waves, which disrupt the reflection by scattering the reflected light rays in all directions. Signal degradation can occur in many ways. Signal degradation can occur if you are trying to communicate over vast distance that the system was not designed for. An example of this is, if the equipment or cable becomes damaged or the antenna becomes blocked. References Oliviero, A., & Woodward, B. (2011). Cabling: The Complete Guide to Copper and Fiber-Optic Networking (4th ed.).

Words: 356 - Pages: 2


...What industry standards body and standards series numbers do you need to reference for Ethernet applications and cabling? a. The Commercial Building Telecommunications Cabling Standard, known as ANSI/TIA/EIA-568-C. b. The IEEE maintains the industry standards for Ethernet protocols, which is part of the 802.3 series of standards. There is an increased need for speed these days and network technology designers are planning to support data rates of up to 100Gbps. 2. What are the different types of Category 6 cable and what should be recommended for this network? a. 10Gbps @ 100 Meters – There are two types of Category 6 cable, regular Category 6, and Category 6A (or Augmented Category 6). It would be my recommendation to use 6A or Category 7. Since we have to support 10Gbps over a maximum of 100 meters, I would recommend using Category 6A, or Category 7 cabling. 3. What cable would you recommend to offer the best shielding performance? a. Full of stray EMI, UTP not an option, and customer wants to ensure capability to operate at 10GBase-T. i. I could recommend a Screened Twisted-Pair Cable or Screened Shielded Twisted-Pair Cable. 4. What type of cable would you use for a. Horizontal Spaces – Plenum cables. Solid Conductor Wire. b. Vertical Spaces – You should use riser-rated cabling in vertical spaces or where flexibility is important. Stranded-conductor wire. 5. What would you look for in trying to find fault if you had the following failures: a. NEXT and......

Words: 341 - Pages: 2

Unit 5 Cabling Factors

...4/14/2014 Unit 5. Assignment 1: Cabling Factors and Tools Discussion Three factors that need to be considered is being fire protected, water proof, and shock protection. Being fire protected, just in case a fire occurs, the wiring would be protected by a casing around the actual wires which in cause wouldn’t melt the casing and destroy the wires. Since the data room is usually in the basement of companies, if a flood occurs, there are wires that are protected by a casing that would not let water intrude into the casing. For shock protection, there is always a chance for a shortage to happen. Wiring and a lot of electricity used. For example, if there is a storm going on and lightning hits a generator and shorts everything out, it would not fry the wiring if they are protected from the shock. The two most important considerations to take into account when either pre-wiring a house or wiring after the house is complete, are the routing of the cable and the quality of the wire used. These two points are often overlooked and the decision to wire the house at all often comes as an afterthought, when most if not all of the interior of the structure has been completed. Some tools that would be useful to use are cable cutters, hole cutting tools, wire strippers, punch down tools, RJ45 connector crimp kits, pliers and cutters, label makers and electrical tape. The makeshift tool that we would use is a staple gun....

Words: 256 - Pages: 2

Copper Cabling vs. Fiber Optic Cabling

...Copper Cabling vs. Fiber Optic cabling The most commonly used copper cables are Cat5e and Cat6. Cat5e cabling is able to support applications requiring bandwidth up to 100MHz and is also offered in a shielded version to prevent interference. Cat6 cabling supports applications requiring bandwidth up to 250MHz and is also available in a shielded version. Also Cat6 cabling is designed to support 1000Base-T (Gigabit Ethernet) (Oliviero, 2010). However, as cost efficient as copper cabling is compared to fiber optics, the maximum horizontal distance is only 90meters (Oliviero, 2010). So if you have a large building or organization you will need to account for the cost of additional hardware like patch panels etc. Fiber optic cables have become very popular over the last ten years because they can be run for longer distances (up to 46.6 miles) and support a higher bandwidth than copper cabling. Fiber optic cabling uses digital light pulses instead of electrical voltage transitions (Oliviero, 2010). This makes it much faster than copper cabling because light is immune to interference, can be modulated to higher frequencies, and travels almost instantaneously to its destination (Oliviero, 2010). Another advantage to fiber optics over copper cabling is security. Copper cabling is susceptible to eavesdropping through taps. Fiber optics are immune to this because they are not electromagnetic. There are three main types of fiber optic cabling, outdoors, indoors, and universal. In......

Words: 520 - Pages: 3

Cabling Definitions

...Montie Ramsarran July 7th, 2014 N1T1310 Mr. Amos Unit 4. Exercise 1. Cabling-Definitions. 1. Horizontal Cable-The cabling between and including the telecommunications outlet and the horizontal cross-connect. Horizontal cabling is considered the permanent portion of a link; may also be called horizontal wiring. 2. Backbone Cable-A cable connection between telecommunications or wiring closets, floor distribution terminals, entrance facilities, and equipment rooms either within or between buildings. This cable can service voice communications or data communications. In star-topology data networks, the backbone cable interconnects hubs and similar devices, as opposed to cables running between hub and station. In a bus topology data network, it is the bus cable. Backbone is also called riser cable, vertical cable, or trunk cable. 3. Patch Cords-Any flexible piece of cable that connects one network device to the main cable run or to a patch panel that in turn connects to the main cable run; also called. Used for interconnecting circuits on a patch panel or cross-connect. Patch cables are short distance, usually have connectors preinstalled on both ends, are used to connect equipment, and are generally between 3 and 6 meters long. 4. Connectors-With respect to cabling, a device attached to the end of a cable, receiver, or light source that joins it with another cable, device or fiber. A connector is a mechanical device used to align......

Words: 1141 - Pages: 5


...applications and cabling? A # 1) The IEEE sustains the industry standards for Ethernet applications and cabling. This is a segment of the 802.3 series of standards and includes applications such as 1000Base-T, 1000Base-SX, 10GBase-T, 10GBase-SR. I found the answer on page 8 in Cabling: The Complete Guide to Copper and Fiber-Optic Networking 4th Edition book. Q # 2) What are the different types of Category 6 cable and what should be recommended for this network? A # 2) Only two different types of 6 cables Category 6, 250 MHZ and Category 6A, 500 MHZ. I would recommend for this network the Category 6A because it has a higher MHZ and as well the network intended to use 10 GB Ethernet with a bandwidth support of 500 MHZ is better than 250MHZ support. The reason I recommend this because of the information on page 8, 12, 17, and 35 in the Cabling: The Complete Guide To Copper and Fiber-Optic networking 4th Edition Book. Q # 3) What Cable would you recommend to offer the best shielding performance? A # 3) I would recommend the S/STP cabling, also known as screened fully shielded twisted – pair (S/FTP), Contains four individually shielded pairs of 24,AWG, 100 ohm wire surrounded by outer metal shielding covering the entire group of shielded copper pairs. This type of cabling offers the best protection from interference from external sources, and also eliminates alien crosstalk, allowing the greatest potential for higher speeds. Sited from page 14 from Cabling: The Complete......

Words: 675 - Pages: 3

Cabling Factor

... shorts in networking hardware, systems that run too hot and placed in tight areas with no ventilation just some examples. Some aspects of proper design are having a detailed plan of how the installation will proceed, you should know the scope of the project, and i.e.…how many cable runs you have what connections need to be made. Your design should also be made available to all people involved with the installation. As well as contain a blueprint of how the cables will be installed. Tools that will be useful in your installation will be, Wire cutters, crimpers, pen and paper, fish tape, pull string, two way radio, labeling materials, punch down tool, toning tools, basic hand tools. I know I have used off the book tools to install cabling. One of the tools I used and it actually stays in the wall is a small plastic funnel. It actually keeps the cable from bending when not going through the back side of the wall. When you cut your spot out where you’re placing your connection box place a small funnel with the cone side in and pull the cable through that actually allows the cable to make a gentle right or left turn rather than being pulled and causing a sharp corner on the cable itself....

Words: 355 - Pages: 2


...The IEEE (Institute of Electrical and Electronics Engineers) maintains the industry standards for Ethernet protocols. The 802.3 series includes Ethernet applications and cabling. The different types of category 6 cable includes CAT6, CAT6A, and CAT6E, although 6E is not an industry recognized standard. I would recommend CAT6A for the possible 10GBASE-T upgrade in the future because it has improved alien crosstalk characteristics when compared to regular CAT6. Unless you decided to go with fiber, you should use STP CAT 6a or CAT7 for a 10gbase-t network, although there were quite a few articles online arguing that shielded cable is unnecessary after going to cat6a or 7 due to higher frequencies that these cable can utilize. The horizontal spaces should use fire retardant plenum cable since it is also used for HVAC. While it might also be prudent to use fire retardant riser cabling for the vertical shafts as well, however if fire stops are placed in the risers you could get away with using regular UTP as well in some places if cost was an issue. The NEXT and FEXT problems could have something to do with having a cable with too many twists, with NEXT the problem would be at the end of the cable where the signal originates, and with FEXT it would be at the opposite end. As the signal rate increases alien crosstalk become more and more of an issue. If it is too much of an issue your best bet might be to upgrade to fiber....

Words: 255 - Pages: 2

Nt1310/Cabling Definitions

...Annette Cattron Mr. Quwaider/NT1310 February 12, 2015 Cabling Definitions 1. Horizontal Cable= The portion of telecommunications cabling that provides connectivity between the horizontal cross-connect and the work-area telecommunications outlet. The horizontal cabling consists of Transmission media, the outlet, the terminations of the horizontal cables, and horizontal cross-connect. 2. Backbone Cable = is the inter-building and intra-building cable connections in structured cabling between entrance facilities, equipment rooms and telecommunications closets. Backbone cabling consists of the transmission media, main and intermediate cross-connects and terminations at these locations. 3. Patch Cords = A patch cord (sometimes called a patch cable) is a length of cable with connectors on the ends that is used to connect an end device to something else, such as a power source. One of the most common uses is connecting a laptop, desktop or other end device to a wall outlet. 4. Connectors = Connector may refer to: Electrical connector, a device for joining electrical circuits together. Audio and video connector, electrical connectors 5. Conduit = a pipe, tube, or tile for protecting electric wires or cables. a means of transmitting or distributing 6. Racks = A computer rack (commonly called a rack) is a metal frame used to hold various hardware devices such as servers, hard disk drives, modems 7. Punch-Down Blocks = A type of terminal strip used to connect telephone...

Words: 851 - Pages: 4

Structured Cabling Homework 1

...Structured Cabling Unit 1 Homework Exercise 1.1 Master it 1. What industry standards body and standards series numbers do you need to reference for Ethernet applications and cabling? A: The IEEE is used as the standard for Ethernet applications and cabling. It is part of the 802.3 series of standards and includes applications such as 1000Base-T, 1000Base-SX, 10GBase-T, and 10GBase-SR. 2. What are the different types of category 6 cables and what should be recommended for this network? A: There are two types of category 6 cables, Cat-6 and Cat-6a I would recommend a Cat-6a for this network since its intended use is for 10 Gigabit Ethernet with a 500MHz bandwidth support. 3. What cable would you recommend to offer the best shielding performance? A: I would recommend a Cat-6a (STP Cable) for this project. My recommendation is based on this cables capability to protect the network from EMI and to operate at 10Base-T. 4. What type of cable would you use for the horizontal spaces and vertical links? A: As for the horizontal spaces, riser-rated cabling is more durable. However, for this project I would recommend a plenum cabling system to prevent toxic fumes if caught on fire. The client is planning to route the cable thought the same space used for air circulation and HVAC. For the Vertical links, I would recommend implementing a rise-related cabling to avoid fore to be spread between floors. “Plenum rated cables can be used in the riser, BUT riser cables cannot......

Words: 417 - Pages: 2